Eric Kerkhoff Selection

Please observe some great offers on Tube Amps

Radial Engineering Headbone Vt Amp Head Switcher For Tube Amps $226.19 Radial Engineering Headbone VT Amp Head Switcher for Tube Amps

Sovtek 12AX7WC Preamp Tube $16.99 The Sovtek 12AX7WC is a very reasonably priced replacement preamp tube. Works in any 12AX7/ECC83 socket. Perfect in Fender and Mesa amps!

Sovtek 12Ax7wc Preamp Tube $16.99 The Sovtek 12AX7WC is a very reasonably priced replacement preamp tube. Works in any 12AX7/ECC83 socket. Perfect in Fender and Mesa amps!

Radial Engineering Tonebone Headbone TS Switcher for Tube to Solid State Amps $259.99 An amplifier head switcher specifically designed to allow you to switch between a solid-state and a tube amp while using the same cabinet. The Headbone employs a series of photocells to assure noise-free guitar-to-head switching and a series of high-cycle relays that switch between the 2 heads and the speaker. A digital programmable interrupt controller receives commands from the onboard footswitch or the Slingshot remote switching system and controls the transition between equipment to ensure proper amplifier loads are always maintained.

JJ Electronics 5AR4 / GZ34 Rectifier Vacuum Tube $23.5 Double anode rectifying tube. A quality, cost-effective replacement for amps that require a 5AR4 rectifier tube.

Jj Electronics 5Ar4 / Gz34 Rectifier Vacuum Tube $23.5 Double anode rectifying tube. A quality, cost-effective replacement for amps that require a 5AR4 rectifier tube.

Radial Engineering Tonebone Headbone Ts Switcher For Tube To Solid State Amps $259.99 An amplifier head switcher specifically designed to allow you to switch between a solid-state and a tube amp while using the same cabinet. The Headbone employs a series of photocells to assure noise-free guitar-to-head switching and a series of high-cycle relays that switch between the 2 heads and the speaker. A digital programmable interrupt controller receives commands from the onboard footswitch or the Slingshot remote switching system and controls the transition between equipment to ensure proper amplifier loads are always maintained.Amp head switcherChoice of direct or buffered inputsEmploys a series of photocells for noise-free switchingHigh-cycle relays switch between the 2 heads and the speakerDigital programmable interrupt controller receives commands from the onboard footswitch or the Slingshot remote switching systemControls the transition between equipment to ensure proper amp loads

Tube $22.99 Tube

Amt Electronics Legend Amps Series V1 Distortion Guitar Effects Pedal $159.95 The AMT Legend Amps Series V1 Distortion Guitar Effects Pedal is intended for the production of sound peculiar to drive channels of Vox* amps. It is distinguished by that classic amp’s specific type of overdrive.AMT Legend Amps is a new revolutionary series of one-channel preamps from AMT Electronics, developed with a new approach to guitar sound formation. Original circuitry was used to produce analog modeling of the physical processes occurring in real vacuum tubes. AMT Legend Amps possess a number of unique features found in real tube preamps and amplifiers: Preamps included into AMT Legend Amps series provide excellent playing dynamics characteristic to real tube-based devices and are in no way inferior to them. With the limitation range similar to tube channel the preamps of the series ensure terrific thickness and power to the resulting sound. Working with AMT Legend Amps preamps you wont feel the urge to cut out the most informative middle frequencies, which in turn will provide great readability of your guitar in the sound mix. Like tube preamps AMT Legend amps provide gradual increase of the limiting stages number as the gain grows. The series preamps use passive circuits of tone shaping which are in full conformity with the tone controls during original tube overdrives. The high level of output signal of AMT Legend Amps (+10 dB at max Level position) corresponds to the tube preamps output signal levels. Thus you have adjustable signal level that makes it possible to connect the preamps to any input (RETURN, DIRECT, LINE etc.) including INPUT POWER AMP* Names used in this document are trademarks of their respective owners, which are in no way associated or affiliated with AMT Electronics. These trademarks of other manufactures were used to identify products whose sounds were reviewed in the making of this product.AMT Legend Amps provide excellent playing dynamics characteristic for purely tube devices not in the least inferior to themWith tube-like limitation the effects of the series provide an amazing density and power of sound. When using AMT Legend Amps you won’t feel the need do cut out the most informative middle frequencies which in turn will provide great readability of your guitar in the mixLike tube preamps AMT Legend amps provide gradual increase in the number of limiting stages as sensitivity growsThe preamps of the series use the passive circuits of tone formation which completely correspond to the adjustments of original tube overdrivesThe high level of the preamps output signal (+10dB at maximum Level position) is the same as of tube preamps. It gives you the adjustable signal level which allows to connect the preamp to any input including Input POWER AMP

Amt Electronics Legend Amps Series S1 Distortion Guitar Effects Pedal $129.95 The AMT Legend Amps Series S1 Distortion Guitar Effects Pedal is intended for the production of sound peculiar to drive channels of Soldano* amps. It is distinguished by a specific type of overdrive: open, wide, and at the same time tough and dynamic.AMT Legend Amps is a new revolutionary series of one-channel preamps from AMT Electronics, developed with a new approach to guitar sound formation. Original circuitry was used to produce analog modeling of the physical processes occurring in real vacuum tubes. AMT Legend Amps possess a number of unique features found in real tube preamps and amplifiers: Preamps included into AMT Legend Amps series provide excellent playing dynamics characteristic to real tube-based devices and are in no way inferior to them. With the limitation range similar to tube channel the preamps of the series ensure terrific thickness and power to the resulting sound. Working with AMT Legend Amps preamps you wont feel the urge to cut out the most informative middle frequencies, which in turn will provide great readability of your guitar in the sound mix. Like tube preamps AMT Legend amps provide gradual increase of the limiting stages number as the gain grows. The series preamps use passive circuits of tone shaping which are in full conformity with the tone controls during original tube overdrives. The high level of output signal of AMT Legend Amps (+10 dB at max Level position) corresponds to the tube preamps output signal levels. Thus you have adjustable signal level that makes it possible to connect the preamps to any input (RETURN, DIRECT, LINE etc.) including INPUT POWER AMP* Names used in this document are trademarks of their respective owners, which are in no way associated or affiliated with AMT Electronics. These trademarks of other manufactures were used to identify products whose sounds were reviewed in the making of this product.AMT Legend Amps provide excellent playing dynamics characteristic for purely tube devices not in the least inferior to themWith tube-like limitation the effects of the series provide an amazing density and power of sound. When using AMT Legend Amps you won’t feel the need do cut out the most informative middle frequencies which in turn will provide great readability of your guitar in the mixLike tube preamps AMT Legend amps provide gradual increase in the number of limiting stages as sensitivity growsThe preamps of the series use the passive circuits of tone formation which completely correspond to the adjustments of original tube overdrivesThe high level of the preamps output signal (+10dB at maximum Level position) is the same as of tube preamps. It gives you the adjustable signal level which allows to connect the preamp to any input including Input POWER AMP

Sovtek 5AR4 Rectifier Tube $24.99 The 5AR4 is Sovtek’s version of a common rectifier tube used in rectifier-equipped high powered amps such as Fender 40W and Vox AC-30 amplifiers. Common to higher powered tube amps, like the later Fender Super Reverb amps and the Vox AC30 (or Matchless copies). May be used to replace a 5U4 or 5Y3 tube and will give a faster more dynamic tonal result. The Sovtek 5AR4 rectifier has a rise time from 300-400 volts that is about 1/2 that of a 5U4 tube. Sovtek 5AR4s work nicely in amps such as the Mesa Rectifier series which use the 5U4. Great if you want a feel and response that is tighter than stock rectifiers yet you want to retain the feel and compression character of a vacuum rectifier over the solid-state setting.

Sovtek 5Ar4 Rectifier Tube $24.99 The 5AR4 is Sovtek’s version of a common rectifier tube used in rectifier-equipped high powered amps such as Fender 40W and Vox AC-30 amplifiers. Common to higher powered tube amps, like the later Fender Super Reverb amps and the Vox AC30 (or Matchless copies). May be used to replace a 5U4 or 5Y3 tube and will give a faster more dynamic tonal result. The Sovtek 5AR4 rectifier has a rise time from 300-400 volts that is about 1/2 that of a 5U4 tube. Sovtek 5AR4s work nicely in amps such as the Mesa Rectifier series which use the 5U4. Great if you want a feel and response that is tighter than stock rectifiers yet you want to retain the feel and compression character of a vacuum rectifier over the solid-state setting.

Radial Engineering Headbone VT Amp Head Switcher for Tube Amps $226.19 As part of the growing line of Tonebone foot pedals, Radial introduces the Headbone VT, a guitar amplifier head switcher that allows the player to transition from, for example, a Mesa Boogie Dual-Rectifier to a Marshall JCM800 while using the same cabinet. The Headbone employs a series of photocells to assure noise-free guitar-to-head switching and a series of high cycle relays that switch between the 2 heads and the speaker. A digital programmable interrupt controller receives commands from the onboard footswitch or the Slingshot remote switching system and controls the transition between equipment to ensure proper amplifier loads are always maintained.Amp head switcherEmploys a series of photocells for noise-free switchingHigh cycle relays switch between the 2 heads and the speakerDigital programmable interrupt controller receives commands from the onboard footswitch or the Slingshot remote switching systemControls the transition between equipment to ensure proper amp loads

Used Radial Engineering Headbone Vt Amp Head Switcher For Tube Amps $226.19 As part of the growing line of Tonebone foot pedals, Radial introduces the Headbone VT, a guitar amplifier head switcher that allows the player to transition from, for example, a Mesa Boogie Dual-Rectifier to a Marshall JCM800 while using the same cabinet. The Headbone employs a series of photocells to assure noise-free guitar-to-head switching and a series of high cycle relays that switch between the 2 heads and the speaker. A digital programmable interrupt controller receives commands from the onboard footswitch or the Slingshot remote switching system and controls the transition between equipment to ensure proper amplifier loads are always maintained.Amp head switcherEmploys a series of photocells for noise-free switchingHigh cycle relays switch between the 2 heads and the speakerDigital programmable interrupt controller receives commands from the onboard footswitch or the Slingshot remote switching systemControls the transition between equipment to ensure proper amp loads

The Amps $4.99 We believe it is important to preserve what makes music special, and make it easy to craft listening experiences. At MOG, browse millions songs and play them instantly. Or just turn on radio where you can stop and replay songs. You can also create playlists for any occasion, and even download songs to your mobile. We are dedicated to employing the cleanest but most powerful technology so you can enjoy music as much as ever.

AMT Electronics Legend Amps Series V1 Distortion Guitar Effects Pedal $159.95 The AMT Legend Amps Series V1 Distortion Guitar Effects Pedal is intended for the production of sound peculiar to «drive» channels of Vox* amps. It is distinguished by that classic amp’s specific type of overdrive.AMT Legend Amps is a new revolutionary series of one-channel preamps from AMT Electronics, developed with a new approach to guitar sound formation. Original circuitry was used to produce analog modeling of the physical processes occurring in real vacuum tubes. AMT Legend Amps possess a number of unique features found in real tube preamps and amplifiers: Preamps included into AMT Legend Amps series provide excellent playing dynamics characteristic to real tube-based devices and are in no way inferior to them. With the limitation range similar to tube channel the preamps of the series ensure terrific thickness and power to the resulting sound. Working with AMT Legend Amps preamps you wont feel the urge to cut out the most informative middle frequencies, which in turn will provide great readability of your guitar in the sound mix. Like tube preamps AMT Legend amps provide gradual increase of the limiting stages number as the gain grows. The series preamps use passive circuits of tone shaping which are in full conformity with the tone controls during original tube overdrives. The high level of output signal of AMT Legend Amps (+10 dB at max Level position) corresponds to the tube preamps output signal levels. Thus you have adjustable signal level that makes it possible to connect the preamps to any input (RETURN, DIRECT, LINE etc.) including INPUT POWER AMP* Names used in this document are trademarks of their respective owners, which are in no way associated or affiliated with AMT Electronics. These trademarks of other manufactures were used to identify products whose sounds were reviewed in the making of this product.

AMT Electronics Legend Amps Series S1 Distortion Guitar Effects Pedal $129.95 The AMT Legend Amps Series S1 Distortion Guitar Effects Pedal is intended for the production of sound peculiar to «drive» channels of Soldano* amps. It is distinguished by a specific type of overdrive: open, wide, and at the same time tough and dynamic.AMT Legend Amps is a new revolutionary series of one-channel preamps from AMT Electronics, developed with a new approach to guitar sound formation. Original circuitry was used to produce analog modeling of the physical processes occurring in real vacuum tubes. AMT Legend Amps possess a number of unique features found in real tube preamps and amplifiers: Preamps included into AMT Legend Amps series provide excellent playing dynamics characteristic to real tube-based devices and are in no way inferior to them. With the limitation range similar to tube channel the preamps of the series ensure terrific thickness and power to the resulting sound. Working with AMT Legend Amps preamps you wont feel the urge to cut out the most informative middle frequencies, which in turn will provide great readability of your guitar in the sound mix. Like tube preamps AMT Legend amps provide gradual increase of the limiting stages number as the gain grows. The series preamps use passive circuits of tone shaping which are in full conformity with the tone controls during original tube overdrives. The high level of output signal of AMT Legend Amps (+10 dB at max Level position) corresponds to the tube preamps output signal levels. Thus you have adjustable signal level that makes it possible to connect the preamps to any input (RETURN, DIRECT, LINE etc.) including INPUT POWER AMP* Names used in this document are trademarks of their respective owners, which are in no way associated or affiliated with AMT Electronics. These trademarks of other manufactures were used to identify products whose sounds were reviewed in the making of this product.

AMT Electronics Legend Amps Series P1 Distortion Guitar Effects Pedal $113.06 The AMT Legend Amps Series P1 Distortion Guitar Effects Pedal was designed to create tones similar to those of the esteemed Peavey 5150*. The sound of the AMT P1 is rich and full in tone, providing tube-like rock distortion. Well defined, clean, clear, cutting, crunchy distortion is what the P1′s all about.AMT Legend Amps is a new revolutionary series of one-channel preamps from AMT Electronics, developed with a new approach to guitar sound formation. Original circuitry was used to produce analog modeling of the physical processes occurring in real vacuum tubes. AMT Legend Amps possess a number of unique features found in real tube preamps and amplifiers: Preamps included into AMT Legend Amps series provide excellent playing dynamics characteristic to real tube-based devices and are in no way inferior to them. With the limitation range similar to tube channel the preamps of the series ensure terrific thickness and power to the resulting sound. Working with AMT Legend Amps preamps you wont feel the urge to cut out the most informative middle frequencies, which in turn will provide great readability of your guitar in the sound mix. Like tube preamps AMT Legend amps provide gradual increase of the limiting stages number as the gain grows. The series preamps use passive circuits of tone shaping which are in full conformity with the tone controls during original tube overdrives. The high level of output signal of AMT Legend Amps (+10 dB at max Level position) corresponds to the tube preamps output signal levels. Thus you have adjustable signal level that makes it possible to connect the preamps to any input (RETURN, DIRECT, LINE etc.) including INPUT POWER AMP* Names used in this document are trademarks of their respective owners, which are in no way associated or affiliated with AMT Electronics. These trademarks of other manufactures were used to identify products whose sounds were reviewed in the making of this product.

AMT Electronics Legend Amps Series M1 Distortion Guitar Effects Pedal $129.95 The AMT Legend Amps Series M1 Distortion Guitar Effects Pedal gets back to the roots of rock. It creates the classic gain of the JCM-800*, giving you Vintage Marshall* style distortion in a compact pedal form. Capture all the tones of one of the most respected, popular guitar amplifiers in rock history. The M1 will open up your sound pallate and playing options without having to spend thousands of dollars on a new rig.AMT Legend Amps is a new revolutionary series of one-channel preamps from AMT Electronics, developed with a new approach to guitar sound formation. Original circuitry was used to produce analog modeling of the physical processes occurring in real vacuum tubes. AMT Legend Amps possess a number of unique features found in real tube preamps and amplifiers: Preamps included into AMT Legend Amps series provide excellent playing dynamics characteristic to real tube-based devices and are in no way inferior to them. With the limitation range similar to tube channel the preamps of the series ensure terrific thickness and power to the resulting sound. Working with AMT Legend Amps preamps you wont feel the urge to cut out the most informative middle frequencies, which in turn will provide great readability of your guitar in the sound mix. Like tube preamps AMT Legend amps provide gradual increase of the limiting stages number as the gain grows. The series preamps use passive circuits of tone shaping which are in full conformity with the tone controls during original tube overdrives. The high level of output signal of AMT Legend Amps (+10 dB at max Level position) corresponds to the tube preamps output signal levels. Thus you have adjustable signal level that makes it possible to connect the preamps to any input (RETURN, DIRECT, LINE etc.) including INPUT POWER AMP* Names used in this document are trademarks of their respective owners, which are in no way associated or affiliated with AMT Electronics. These trademarks of other manufactures were used to identify products whose sounds were reviewed in the making of this product.

AMT Electronics Legend Amps Series B1 Distortion Guitar Effects Pedal $129.95 The AMT Legend Amps Series B1 Distortion Guitar Effects Pedal creates superior high gain quality distortion, as found in the Bogner Sharp Channel Amplifier*. The sound of the AMT B1 is monstrous in tone, aggression, and provides massive amounts of gain. Thunderous lows, screaming highs, and scoopable mids leave you with unbeatable heavy distortion sounds.AMT Legend Amps is a new revolutionary series of one-channel preamps from AMT Electronics, developed with a new approach to guitar sound formation. Original circuitry was used to produce analog modeling of the physical processes occurring in real vacuum tubes. AMT Legend Amps possess a number of unique features found in real tube preamps and amplifiers: Preamps included into AMT Legend Amps series provide excellent playing dynamics characteristic to real tube-based devices and are in no way inferior to them. With the limitation range similar to tube channel the preamps of the series ensure terrific thickness and power to the resulting sound. Working with AMT Legend Amps preamps you wont feel the urge to cut out the most informative middle frequencies, which in turn will provide great readability of your guitar in the sound mix. Like tube preamps AMT Legend amps provide gradual increase of the limiting stages number as the gain grows. The series preamps use passive circuits of tone shaping which are in full conformity with the tone controls during original tube overdrives. The high level of output signal of AMT Legend Amps (+10 dB at max Level position) corresponds to the tube preamps output signal levels. Thus you have adjustable signal level that makes it possible to connect the preamps to any input (RETURN, DIRECT, LINE etc.) including INPUT POWER AMP* Names used in this document are trademarks of their respective owners, which are in no way associated or affiliated with AMT Electronics. These trademarks of other manufactures were used to identify products whose sounds were reviewed in the making of this product.

AMT Electronics Legend Amps Series E1 Distortion Guitar Effects Pedal $129.95 The AMT Legend Amps Series E1 Distortion Guitar Effects Pedal is the preliminary amplifier for the fans of juicy sound with resilient mids. It emulates the Lead channel of such legends as the ENGL Fireball*. AMT Legend Amps E-1 is the resilient, aggressive distortion, for which ENGL* amps are famous. The wide range of sensitivity adjustment allows you to receive classic biting rock sound with minimum efforts. At bigger distortion the sound acquires metallic colors with great sustain, bright flageolets and readability of even complex chords at any distortion level characteristic of Engl* amps.AMT Legend Amps is a new revolutionary series of one-channel preamps from AMT Electronics, developed with a new approach to guitar sound formation. Original circuitry was used to produce analog modeling of the physical processes occurring in real vacuum tubes. AMT Legend Amps possess a number of unique features found in real tube preamps and amplifiers: Preamps included into AMT Legend Amps series provide excellent playing dynamics characteristic to real tube-based devices and are in no way inferior to them. With the limitation range similar to tube channel the preamps of the series ensure terrific thickness and power to the resulting sound. Working with AMT Legend Amps preamps you wont feel the urge to cut out the most informative middle frequencies, which in turn will provide great readability of your guitar in the sound mix. Like tube preamps AMT Legend amps provide gradual increase of the limiting stages number as the gain grows. The series preamps use passive circuits of tone shaping which are in full conformity with the tone controls during original tube overdrives. The high level of output signal of AMT Legend Amps (+10 dB at max Level position) corresponds to the tube preamps output signal levels. Thus you have adjustable signal level that makes it possible to connect the preamps to any input (RETURN, DIRECT, LINE etc.) including INPUT POWER AMP* Names used in this document are trademarks of their respective owners, which are in no way associated or affiliated with AMT Electronics. These trademarks of other manufactures were used to identify products whose sounds were reviewed in the making of this product.

Fender Tbfs-4 4-Button Footswitch For Tb1200/600 Bass Amps Black $59.99 The Fender TBFS-4 is a 4-button footswitch that adds functionality to Fender TB1200 and TB600 Bass Amplifiers. With this stompbox you have foot control of the Tube Overdrive, Blend Vari-Q, FX loop, and Mute features of the amps. Fender includes a built-in tuner with the TBFS-4 footswitch.

Taco Led Tube Light $59.99 Taco Led Tube Light . The Tube Light is great for use in engine rooms, T-tops and arches. Universal design for use as is, or replacement light for existing standard T-top light housings. 108 LEDs provide high output, low glare light and draw only .25 amps. Switch from white light to red light for chart-reading with the addition of a toggle switch. Impact-resistant Polycarbonate lens. Light tube and connection sealed for water resistance. Mounting clips included for easy installations. 20-1/2″L.

THD Triode Yellow Jacket for 7591 Amps Duet $118 The YJ7591D is an adapter that permits the use of an EL84 power tube in 7591 amps. There are no adjustments to make and no modifications are necessary. You simply plug the Yellow Jacket into the amp’s output tube sockets, plug the provided EL84s into the Yellow Jacket, turn on the amp, and play. THD’s Yellow Jacket converters not only rearrange the pin locations of the tubes, but also provide the necessary current limiting on the screens and cathode as well as blocking the amplifier’s grid-bias voltage, configuring the EL84 in a Class-A, self-adjusting cathode-bias circuit. When the Yellow Jacket Converters are installed in larger amplifiers intended for 6L6s or EL34 output tubes, the high plate and screen voltages are reduced as well as current limited to protect the EL84 and to drop output power. When a pair of Yellow Jacket are used in a Marshall 50W or similar amplifier, the overall power drops to about 20W and takes on more of the character of an old Vox AC30. The distortion is smoother and more even and the output is both substantially reduced and more compressed due to the Class-A nature of the Yellow Jackets. In a 100W amp like a Twin Reverb or Marshall 100, either 2 or 4 Yellow Jackets can be used. If only 2 are used and the other 2 sockets are left empty, the output is dropped to about 20 watts. With 4 in place, the amp puts out about 40W and takes on a whole new warmth and richness. Will they hurt your amp? No! Yellow Jacket converters are safe for all amplifiers and transformers. As all Yellow Jacket converters internally regulates voltage and current they put no extra strain on amplifiers’ power and output transformers or internal components. Using the Yellow Jacket in higher powered amplifiers actually reduces the strain on the transformers and internal components because it reduces the overall wattage of the system. Furthermore, the heater (or filament) current of the EL84 is lower than that of the 6L6, EL34 or 7591, so the Yellow Jacket will reduce the strain on the filament windings of the power transformer as well.Use an EL84 in 7591 amps Tubes included

Thd Triode Yellow Jacket For 7591 Amps Duet $118 The YJ7591D is an adapter that permits the use of an EL84 power tube in 7591 amps. There are no adjustments to make and no modifications are necessary. You simply plug the Yellow Jacket into the amp’s output tube sockets, plug the provided EL84s into the Yellow Jacket, turn on the amp, and play. THD’s Yellow Jacket converters not only rearrange the pin locations of the tubes, but also provide the necessary current limiting on the screens and cathode as well as blocking the amplifier’s grid-bias voltage, configuring the EL84 in a Class-A, self-adjusting cathode-bias circuit. When the Yellow Jacket Converters are installed in larger amplifiers intended for 6L6s or EL34 output tubes, the high plate and screen voltages are reduced as well as current limited to protect the EL84 and to drop output power. When a pair of Yellow Jacket are used in a Marshall 50W or similar amplifier, the overall power drops to about 20W and takes on more of the character of an old Vox AC30. The distortion is smoother and more even and the output is both substantially reduced and more compressed due to the Class-A nature of the Yellow Jackets. In a 100W amp like a Twin Reverb or Marshall 100, either 2 or 4 Yellow Jackets can be used. If only 2 are used and the other 2 sockets are left empty, the output is dropped to about 20 watts. With 4 in place, the amp puts out about 40W and takes on a whole new warmth and richness. Will they hurt your amp? No! Yellow Jacket converters are safe for all amplifiers and transformers. As all Yellow Jacket converters internally regulates voltage and current they put no extra strain on amplifiers’ power and output transformers or internal components. Using the Yellow Jacket in higher powered amplifiers actually reduces the strain on the transformers and internal components because it reduces the overall wattage of the system. Furthermore, the heater (or filament) current of the EL84 is lower than that of the 6L6, EL34 or 7591, so the Yellow Jacket will reduce the strain on the filament windings of the power transformer as well.Use an EL84 in 7591 amps Tubes included

Groove Tubes Gold Series Gt-6C4 Rectifier Tube $19.95 The Groove Tubes GT-6C4 Rectifier Tube is a common 9 -in rectifier for smaller amps like the Silverstone guitar/amp case combos of the 50′s.

Electro-Harmonix 12AX7EH Preamp Tube $12.99 The Electro-Harmonix 12AX7EH is a preamp tube that provides high gain with ultra low noise. The tube’s detailed, musical tone rivals the most desirable NOS types. Unique spiral filament eliminates the filament-to-cathode induced hum common on amps that use AC on the filaments.

Amt Electronics Legend Amps Series E1 Distortion Guitar Effects Pedal $129.95 The AMT Legend Amps Series E1 Distortion Guitar Effects Pedal is the preliminary amplifier for the fans of juicy sound with resilient mids. It emulates the Lead channel of such legends as the ENGL Fireball*. AMT Legend Amps E-1 is the resilient, aggressive distortion, for which ENGL* amps are famous. The wide range of sensitivity adjustment allows you to receive classic biting rock sound with minimum efforts. At bigger distortion the sound acquires metallic colors with great sustain, bright flageolets and readability of even complex chords at any distortion level characteristic of Engl* amps.AMT Legend Amps is a new revolutionary series of one-channel preamps from AMT Electronics, developed with a new approach to guitar sound formation. Original circuitry was used to produce analog modeling of the physical processes occurring in real vacuum tubes. AMT Legend Amps possess a number of unique features found in real tube preamps and amplifiers: Preamps included into AMT Legend Amps series provide excellent playing dynamics characteristic to real tube-based devices and are in no way inferior to them. With the limitation range similar to tube channel the preamps of the series ensure terrific thickness and power to the resulting sound. Working with AMT Legend Amps preamps you wont feel the urge to cut out the most informative middle frequencies, which in turn will provide great readability of your guitar in the sound mix. Like tube preamps AMT Legend amps provide gradual increase of the limiting stages number as the gain grows. The series preamps use passive circuits of tone shaping which are in full conformity with the tone controls during original tube overdrives. The high level of output signal of AMT Legend Amps (+10 dB at max Level position) corresponds to the tube preamps output signal levels. Thus you have adjustable signal level that makes it possible to connect the preamps to any input (RETURN, DIRECT, LINE etc.) including INPUT POWER AMP* Names used in this document are trademarks of their respective owners, which are in no way associated or affiliated with AMT Electronics. These trademarks of other manufactures were used to identify products whose sounds were reviewed in the making of this product.The AMT Legend Amp Series guitar pedals provide excellent dynamics, nuances, and characteristics similar to that of tube driven amplifiersTube-like range of volume control provides great sound density, playability, and power when playing at full volume and also in conjunction with your guitars volume knobTRUE BYPASS. The preamps of the Legend Amp Series pedals use passive true bypass circuitry, therefore no loss of guitar signal is noticed in your pedal chain. Similar to if no pedal was there at all when bypassedFeatures high level of output signal (+10dB in extreme position of Level knob) corresponds to the output levels similar of tube preamps. Thus, you have adjustable signal level allowing to hook up your preamp AND direct input of a power ampli

Electro-Harmonix 12Ax7eh Preamp Tube $12.99 The Electro-Harmonix 12AX7EH is a preamp tube that provides high gain with ultra low noise. The tube’s detailed, musical tone rivals the most desirable NOS types. Unique spiral filament eliminates the filament-to-cathode induced hum common on amps that use AC on the filaments.

Understanding Vacuum Tube Guitar Amplifiers - $59.99 Gerald Weber, president of Kendrick Amplifiers, guides viewers through the nuts and bolts of vacuum tube guitar amps in this detailed instructional program. Useful for professionals and beginners alike, this title includes useful tips about AC and DC voltage and current, tone shaping, vacuum tube types, and much more. ~ Carly Wray, Rovi

Amt Electronics Legend Amps Series P1 Distortion Guitar Effects Pedal $129.95 The AMT Legend Amps Series P1 Distortion Guitar Effects Pedal was designed to create tones similar to those of the esteemed Peavey 5150*. The sound of the AMT P1 is rich and full in tone, providing tube-like rock distortion. Well defined, clean, clear, cutting, crunchy distortion is what the P1′s all about.AMT Legend Amps is a new revolutionary series of one-channel preamps from AMT Electronics, developed with a new approach to guitar sound formation. Original circuitry was used to produce analog modeling of the physical processes occurring in real vacuum tubes. AMT Legend Amps possess a number of unique features found in real tube preamps and amplifiers: Preamps included into AMT Legend Amps series provide excellent playing dynamics characteristic to real tube-based devices and are in no way inferior to them. With the limitation range similar to tube channel the preamps of the series ensure terrific thickness and power to the resulting sound. Working with AMT Legend Amps preamps you wont feel the urge to cut out the most informative middle frequencies, which in turn will provide great readability of your guitar in the sound mix. Like tube preamps AMT Legend amps provide gradual increase of the limiting stages number as the gain grows. The series preamps use passive circuits of tone shaping which are in full conformity with the tone controls during original tube overdrives. The high level of output signal of AMT Legend Amps (+10 dB at max Level position) corresponds to the tube preamps output signal levels. Thus you have adjustable signal level that makes it possible to connect the preamps to any input (RETURN, DIRECT, LINE etc.) including INPUT POWER AMP* Names used in this document are trademarks of their respective owners, which are in no way associated or affiliated with AMT Electronics. These trademarks of other manufactures were used to identify products whose sounds were reviewed in the making of this product.The AMT Legend Amp Series guitar pedals provide excellent dynamics, nuances, and characteristics similar to that of tube driven amplifiers Tube-like range of volume control provides great sound density, playability, and power when playing at full volume and also in conjunction with your guitars volume knobTRUE BYPASS. The preamps of the Legend Amp Series pedals use passive true bypass circuitry, therefore no loss of guitar signal is noticed in your pedal chain. Similar to if no pedal was there at all when bypassedFeatures high level of output signal (+10dB in extreme position of Level knob) corresponds to the output levels similar of tube preamps. Thus, you have adjustable signal level allowing to hook up your preamp AND direct input of a power amplifier Controls include LEVEL, GAIN, LOW, MID, and HIGHTWO signal outputs: DIRECT AMPLIFIER OUT for guitar amplifier use and CAB SIMULATION OUT for mixer, or studio use

Groove Tubes Gold Series GT-12AU7 Preamp Tube $13.95 The Groove Tubes GT-12AU7 preamp tube is based on a design from the Ei factory in the former Yugoslavia. The GT-12AU7 is an excellent quality large-plate European-made driver tube, styled after the famous Telefunken line of dual triodes. The usual application for a 12AU7 tube is as the phase inverter that drives the power tubes. These are very well matched, and so are highly recommended for Ampeg SVT’s and other amps using this tube as a phase inverter. Also commonly used as phase inverters in McIntosh Hi-Fi amps, some Ampeg amps, and will yield the most clean headroom in many amps. In the latest Fender Pro Series amps such as the Pro Reverb, Concert, and Twin, this tube in V2 (or a 12AY7), will drop the gain of the gain channel where some feel the tone is of a less intense or “buzzy” character. This will then allow a much wider range in the sweep of the volume and gain controls of this channel.Country of origin: ChinaCountry of origin: China

Groove Tubes Gold Series Gt-12Au7 Preamp Tube $13.95 The Groove Tubes GT-12AU7 preamp tube is based on a design from the Ei factory in the former Yugoslavia. The GT-12AU7 is an excellent quality large-plate European-made driver tube, styled after the famous Telefunken line of dual triodes. The usual application for a 12AU7 tube is as the phase inverter that drives the power tubes. These are very well matched, and so are highly recommended for Ampeg SVT’s and other amps using this tube as a phase inverter. Also commonly used as phase inverters in McIntosh Hi-Fi amps, some Ampeg amps, and will yield the most clean headroom in many amps. In the latest Fender Pro Series amps such as the Pro Reverb, Concert, and Twin, this tube in V2 (or a 12AY7), will drop the gain of the gain channel where some feel the tone is of a less intense or “buzzy” character. This will then allow a much wider range in the sweep of the volume and gain controls of this channel.Country of origin: ChinaCountry of origin: China

Amt Electronics Legend Amps Series B1 Distortion Guitar Effects Pedal $129.95 The AMT Legend Amps Series B1 Distortion Guitar Effects Pedal creates superior high gain quality distortion, as found in the Bogner Sharp Channel Amplifier*. The sound of the AMT B1 is monstrous in tone, aggression, and provides massive amounts of gain. Thunderous lows, screaming highs, and scoopable mids leave you with unbeatable heavy distortion sounds.AMT Legend Amps is a new revolutionary series of one-channel preamps from AMT Electronics, developed with a new approach to guitar sound formation. Original circuitry was used to produce analog modeling of the physical processes occurring in real vacuum tubes. AMT Legend Amps possess a number of unique features found in real tube preamps and amplifiers: Preamps included into AMT Legend Amps series provide excellent playing dynamics characteristic to real tube-based devices and are in no way inferior to them. With the limitation range similar to tube channel the preamps of the series ensure terrific thickness and power to the resulting sound. Working with AMT Legend Amps preamps you wont feel the urge to cut out the most informative middle frequencies, which in turn will provide great readability of your guitar in the sound mix. Like tube preamps AMT Legend amps provide gradual increase of the limiting stages number as the gain grows. The series preamps use passive circuits of tone shaping which are in full conformity with the tone controls during original tube overdrives. The high level of output signal of AMT Legend Amps (+10 dB at max Level position) corresponds to the tube preamps output signal levels. Thus you have adjustable signal level that makes it possible to connect the preamps to any input (RETURN, DIRECT, LINE etc.) including INPUT POWER AMP* Names used in this document are trademarks of their respective owners, which are in no way associated or affiliated with AMT Electronics. These trademarks of other manufactures were used to identify products whose sounds were reviewed in the making of this product.The AMT Legend Amp Series guitar pedals provide excellent dynamics, nuances, and characteristics similar to that of tube driven amplifiersTube-like range of volume control provides great sound density, playability, and power when playing at full volume and also in conjunction with your guitars volume knob TRUE BYPASS. The preamps of the Legend Amp Series pedals use passive true bypass circuitry, therefore no loss of guitar signal is noticed in your pedal chain. Similar to if no pedal was there at all when bypassed Features high level of output signal (+10dB in extreme position of Level knob) corresponds to the output levels similar of tube preamps. Thus, you have adjustable signal level allowing to hook up your preamp AND direct input of a power amplifierControls include LEVEL, GAIN, LOW, MID, and HIGH TWO signal outputs: DIRECT AMPLIFIER OUT for guitar amplifier use and CAB SIMULATION OUT for mixer, or studio use

Amt Electronics Legend Amps Series M1 Distortion Guitar Effects Pedal $129.95 The AMT Legend Amps Series M1 Distortion Guitar Effects Pedal gets back to the roots of rock. It creates the classic gain of the JCM-800*, giving you Vintage Marshall* style distortion in a compact pedal form. Capture all the tones of one of the most respected, popular guitar amplifiers in rock history. The M1 will open up your sound pallate and playing options without having to spend thousands of dollars on a new rig.AMT Legend Amps is a new revolutionary series of one-channel preamps from AMT Electronics, developed with a new approach to guitar sound formation. Original circuitry was used to produce analog modeling of the physical processes occurring in real vacuum tubes. AMT Legend Amps possess a number of unique features found in real tube preamps and amplifiers: Preamps included into AMT Legend Amps series provide excellent playing dynamics characteristic to real tube-based devices and are in no way inferior to them. With the limitation range similar to tube channel the preamps of the series ensure terrific thickness and power to the resulting sound. Working with AMT Legend Amps preamps you wont feel the urge to cut out the most informative middle frequencies, which in turn will provide great readability of your guitar in the sound mix. Like tube preamps AMT Legend amps provide gradual increase of the limiting stages number as the gain grows. The series preamps use passive circuits of tone shaping which are in full conformity with the tone controls during original tube overdrives. The high level of output signal of AMT Legend Amps (+10 dB at max Level position) corresponds to the tube preamps output signal levels. Thus you have adjustable signal level that makes it possible to connect the preamps to any input (RETURN, DIRECT, LINE etc.) including INPUT POWER AMP* Names used in this document are trademarks of their respective owners, which are in no way associated or affiliated with AMT Electronics. These trademarks of other manufactures were used to identify products whose sounds were reviewed in the making of this product.The AMT Legend Amp Series guitar pedals provide excellent dynamics, nuances, and characteristics similar to that of tube driven amplifiersTube-like range of volume control provides great sound density, playability, and power when playing at full volume and also in conjunction with your guitars volume knobTRUE BYPASS. The preamps of the Legend Amp Series pedals use passive true bypass circuitry, therefore no loss of guitar signal is noticed in your pedal chain. Similar to if no pedal was there at all when bypassedFeatures high level of output signal (+10dB in extreme position of Level knob) corresponds to the output levels similar of tube preamps. Thus, you have adjustable signal level allowing to hook up your preamp AND direct input of a power amplifierControls include LEVEL, GAIN, LOW, MID, and HIGH TWO signal outputs: DIRECT AMPLIFIER OUT for guitar amplifier use and CAB SIMULATION OUT for mixer, or studio use

Softube Tube Delay NATIVE $89.99 The Tube Delay plug-in from Softube is a marriage between analog and digital, combining the warmth and natural compression from tubes with the features and versatility of a digital delay. The effect is perfect for fattening vocal tracks, adding slapback echo to drums, or getting a gritty delay for guitars. The Tube Delay software gives you authentic tube simulation using the same technology as Softube’s Amp Room products on both the dry and wet signal. In total, you get three different tube stagesin the direct, delayed, and feedbacked signal. It also provides vintage-style passive EQ with Bass and Treble that affects both the dry and the wet signal and also boosts the distortion popular in classic American guitar amps. Get delay time from 1 ms to 1 second with a host tempo sync option that sets the delay time from 16th notes to half notes with the triplets in between.

AMT Electronics Legend Amps Series F1 Distortion Guitar Effects Pedal $159.95 The AMT Legend Amps Series F1 Distortion Guitar Effects Pedal is intended for studio use and live performances. AMT F-1 is a preamp with internal CLEAN channel and the possibility of switching to an external channel (any auxiliary overdrive effect) by means of a foot switch. AMT F-1 has the insert loop of serial type with standard -10dB level intended for connection of auxiliary effects and boosting the effect signal to standard 0dB level or higher (MASTER VOLUME), which is sufficient to operate directly with power amplifier. In case of connection to a mixer the preamp has speaker simulator mode. The mode can be selected by the switch loicated on the left panel of the device. AMT F-1 provides the built-in power hub to supply 912V to external channel and auxiliary effects.The bottom of the AMT F-1 (under the boxs cover) has an FX. Loop mode switch serial/parallel, which significantly expands your choices. In case of connection to Ch. send, Ch. return, there is a bi-color LED indicator (located on the front panel): Clean channel AMT F-1 – green, Lead external channel – red. If AMT F-1 is used in mono mode (without external overdriven channels) the LED is single-colored and the footswitch acts as «Bypass» Clean channel AMT F-1.AMT Legend Amps is a new revolutionary series of one-channel preamps from AMT Electronics, developed with a new approach to guitar sound formation. Original circuitry was used to produce analog modeling of the physical processes occurring in real vacuum tubes. AMT Legend Amps possess a number of unique features found in real tube preamps and amplifiers: Preamps included into AMT Legend Amps series provide excellent playing dynamics characteristic to real tube-based devices and are in no way inferior to them. With the limitation range similar to tube channel the preamps of the series ensure terrific thickness and power to the resulting sound. Working with AMT Legend Amps preamps you wont feel the urge to cut out the most informative middle frequencies, which in turn will provide great readability of your guitar in the sound mix. Like tube preamps AMT Legend amps provide gradual increase of the limiting stages number as the gain grows. The series preamps use passive circuits of tone shaping which are in full conformity with the tone controls during original tube overdrives. The high level of output signal of AMT Legend Amps (+10 dB at max Level position) corresponds to the tube preamps output signal levels. Thus you have adjustable signal level that makes it possible to connect the preamps to any input (RETURN, DIRECT, LINE etc.) including INPUT POWER AMP* Names used in this document are trademarks of their respective owners, which are in no way associated or affiliated with AMT Electronics. These trademarks of other manufactures were used to identify products whose sounds were reviewed in the making of this product.

Amt Electronics Legend Amps Series F1 Distortion Guitar Effects Pedal $159.95 The AMT Legend Amps Series F1 Distortion Guitar Effects Pedal is intended for studio use and live performances. AMT F-1 is a preamp with internal CLEAN channel and the possibility of switching to an external channel (any auxiliary overdrive effect) by means of a foot switch. AMT F-1 has the insert loop of serial type with standard -10dB level intended for connection of auxiliary effects and boosting the effect signal to standard 0dB level or higher (MASTER VOLUME), which is sufficient to operate directly with power amplifier. In case of connection to a mixer the preamp has speaker simulator mode. The mode can be selected by the switch loicated on the left panel of the device. AMT F-1 provides the built-in power hub to supply 912V to external channel and auxiliary effects.The bottom of the AMT F-1 (under the boxs cover) has an FX. Loop mode switch serial/parallel, which significantly expands your choices. In case of connection to Ch. send, Ch. return, there is a bi-color LED indicator (located on the front panel): Clean channel AMT F-1 – green, Lead external channel – red. If AMT F-1 is used in mono mode (without external overdriven channels) the LED is single-colored and the footswitch acts as Bypass Clean channel AMT F-1.AMT Legend Amps is a new revolutionary series of one-channel preamps from AMT Electronics, developed with a new approach to guitar sound formation. Original circuitry was used to produce analog modeling of the physical processes occurring in real vacuum tubes. AMT Legend Amps possess a number of unique features found in real tube preamps and amplifiers: Preamps included into AMT Legend Amps series provide excellent playing dynamics characteristic to real tube-based devices and are in no way inferior to them. With the limitation range similar to tube channel the preamps of the series ensure terrific thickness and power to the resulting sound. Working with AMT Legend Amps preamps you wont feel the urge to cut out the most informative middle frequencies, which in turn will provide great readability of your guitar in the sound mix. Like tube preamps AMT Legend amps provide gradual increase of the limiting stages number as the gain grows. The series preamps use passive circuits of tone shaping which are in full conformity with the tone controls during original tube overdrives. The high level of output signal of AMT Legend Amps (+10 dB at max Level position) corresponds to the tube preamps output signal levels. Thus you have adjustable signal level that makes it possible to connect the preamps to any input (RETURN, DIRECT, LINE etc.) including INPUT POWER AMP* Names used in this document are trademarks of their respective owners, which are in no way associated or affiliated with AMT Electronics. These trademarks of other manufactures were used to identify products whose sounds were reviewed in the making of this product.Clean sounding preamp with external overdrive channel routingAdditional effects loop2 outputs to power other effects

Jacques TB-2 Tube Blower Overdrive Pedal $129.95 The Jacques TB-2 Tube Blower is an overdrive pedal designed in the tradition of the original Ibanez ts808. The Jacques Tube Blower is a boutique pedal that improves on the legendary Tube Screamer’s performance by adding more gain, continuous morphing from clean to gain, bass boost a la Marshall amps, and treble boost a la Fender black face amps. The Tube Blower also offers you full single-coil and humbucker compatibility, transparency to the amp, transparency to the guitar and playing style, and a classic look. The Jacques TB-2 Tube Blower Overdrive Pedal also give you low and high boost, drive, and level controls.

Kendrick Tube Guitar Amplifier Servicing and Overhaul (DVD) $69.95 Kendrick Amplifier President and Vintage Guitar magazine columnist Gerald Weber has overhauled and restored over 15,000 vintage tube guitar amps. This extensive DVD covers: basics of servicing and overhauling a tube guitar amp, what tools are needed, the wiring mistake made on 50% of all amps and how to correct it, the best way to straighten preamp tube pins, how to perform a cap job correctly, the different types of Silverface amps and how to convert each to Blackface, how to identify leads of an unknown transformer, how to make perfect chassis grounds, and much, much more! Nearly four hours.Size: 5.25″ x 7.50″Editor: Gerald WeberISBN: 1423409973

Kendrick Tube Guitar Amplifier Servicing And Overhaul (Dvd) $69.95 Kendrick Amplifier President and Vintage Guitar magazine columnist Gerald Weber has overhauled and restored over 15,000 vintage tube guitar amps. This extensive DVD covers: basics of servicing and overhauling a tube guitar amp, what tools are needed, the wiring mistake made on 50% of all amps and how to correct it, the best way to straighten preamp tube pins, how to perform a cap job correctly, the different types of Silverface amps and how to convert each to Blackface, how to identify leads of an unknown transformer, how to make perfect chassis grounds, and much, much more! Nearly four hours.Size: 5.25″ x 7.50″Editor: Gerald WeberISBN: 1423409973

Groove Tubes Gold Series GT-6CA4 Rectifier Tube $27.95 The Groove Tubes Gold Series GT-6CA4 Rectifier Tube is a common 9-pin rectifier for smaller amps like the Silverstone guitar/amp case combos of the 50′s.Country of origin: ChinaCountry of origin: China

Groove Tubes Gold Series Gt-6Ca4 Rectifier Tube $27.95 The Groove Tubes Gold Series GT-6CA4 Rectifier Tube is a common 9-pin rectifier for smaller amps like the Silverstone guitar/amp case combos of the 50′s.Country of origin: ChinaCountry of origin: China

Hughes & Kettner Tube Factor Overdrive Pedal $279 By feeding sufficient juice (upwards of 300V) to its tube-based tone circuitry, this pedal gives you the real thing: a warm tube clean sound and a blistering, saturated-tube lead sound. Both are available at the press of a switch. The Tube Factor is the key to getting the hottest lead sounds from vintage amps and genuine tube tone from solid state combos. In effect, it expands any amp with an additional channel.

Softube Tube Delay Native $89.99 The Tube Delay plug-in from Softube is a marriage between analog and digital, combining the warmth and natural compression from tubes with the features and versatility of a digital delay. The effect is perfect for fattening vocal tracks, adding slapback echo to drums, or getting a gritty delay for guitars. The Tube Delay software gives you authentic tube simulation using the same technology as Softube’s Amp Room products on both the dry and wet signal. In total, you get three different tube stagesin the direct, delayed, and feedbacked signal. It also provides vintage-style passive EQ with Bass and Treble that affects both the dry and the wet signal and also boosts the distortion popular in classic American guitar amps. Get delay time from 1 ms to 1 second with a host tempo sync option that sets the delay time from 16th notes to half notes with the triplets in between.1 millisecond to 1 second delaySync tempo to hostVintage-style passive EQGritty feedback featureTube preamp simulatonOnly available for native VST/AU/RTAS hosts on Mac and Windows

Manley Tube Direct Interface – Mono $810 The Manley Tube Direct Interface features exceptionally clean and quiet tube circuits, which will warm up any electric guitar, bass, violin, and especially those sterile sounding synths. Unique with the Manley Tube DI’s is the added 5-position high pass shelf EQ, there to fight unwanted resonances. As a splitter device, the transformer-coupled balanced XLR output can be sent directly to a mic level input, such as through your console channel, while the 1/4″ output drives the guitar amplifier cabinet, which can be miked and mixed with the direct feed. Low impedance outputs, Ground lift and Console Out Boost switches make the Manley tube DI box both versatile and compatible. Keep your Manley interface close at hand to get that noisy high impedance guitar cable into quiet lo-Z territory fast!Vacuum Tube: 5751Gain: -6dB or -26dBInput Z: 10 Mohm to 1 MohmOutput Z: 150 ohm xfmrFrequency response: 12 Hz 15KHz (-3dB)EQ: LF rolloff -3dB points: 12, 42, 100, 250HzTransformer-Coupled Balanced XLR OutputConsole Out Boost SwitchGround Lift SwitchFactory set for 100V, 120V or 220-240VAC operation for original destination country’s mains voltage.Operating Mains Voltage changeable with power transformer re-wiring and fuse value change.Mains Voltage Frequency: 50~ 60HzMains power consumption Mono Tube DI:0.050 Amps (50 milliamps = 50mA) @ 120V = 6 Watts0.025 Amps (25 milliamps = 25mA) @ 240V = 6 WattsMains power consumption Stereo Tube DI:0.0750 Amps (75 milliamps = 75mA) @ 120V = 9 Watts0.0375 Amps (37.5 milliamps = 37.5mA) @ 240V = 9 Watts

Groove Tubes Silver Series ST-7027-S Power Tube $18.95 The Groove Tubes Silver Series ST-7027-S Power Tube is a rare power pentode used in early Ampeg amps and a good tube in all areas. The only option for an Ampeg VT22 or V4. Country of origin: SlovakiaNEW SILVER SERIES TUBESGroove Tubes Silver Series are tested and warranted to meet or exceed factory specifications.Silver Series tubes are excellent for “normal” tube replacement applications and offer exceptional value.Not recommended for the critical high gain V1 stages of high gain guitar amps, but perfect for the other less critical stages such as V2-V6 stages.Country of origin: Slovakia

Groove Tubes Silver Series St-7027-S Power Tube $18.95 The Groove Tubes Silver Series ST-7027-S Power Tube is a rare power pentode used in early Ampeg amps and a good tube in all areas. The only option for an Ampeg VT22 or V4. Country of origin: SlovakiaNEW SILVER SERIES TUBESGroove Tubes Silver Series are tested and warranted to meet or exceed factory specifications.Silver Series tubes are excellent for “normal” tube replacement applications and offer exceptional value.Not recommended for the critical high gain V1 stages of high gain guitar amps, but perfect for the other less critical stages such as V2-V6 stages.Country of origin: Slovakia

Groove Tubes Silver Series St-7591-R Power Tube $30.95 The Groove Tubes Silver Series ST-7591-R Power Tube is a somewhat obscure pentode tube used in some early Gibson amps that had been off the market. Recently, a Russian factory decided to supply it again. Groove Tubes ST-7591-R tubes are made in very low quantities and are a close copy of the original vacuum tube.Country of origin: Russia NEW SILVER SERIES TUBESGroove Tubes Silver Series are tested and warranted to meet or exceed factory specifications.Silver Series tubes are excellent for “normal” tube replacement applications and offer exceptional value.Not recommended for the critical high gain V1 stages of high gain guitar amps, but perfect for the other less critical stages such as V2-V6 stages.Country of origin: Russia

Groove Tubes Gold Series GT-5Y3 GZ30 Rectifier Tube $17.99 The Groove Tubes Gold Series GT-5Y3″GZ30 is a rectifier tube common to lower-powered Fender amplifiers such as the Champ, Princeton and Deluxe amps. This Gold Series vacuum tube can be used in many 5AR4 and 5U4 amps for lower levels. This Groove Tubes rectifier may be used in amps such as the Matchless DC-30 series and similar amps when you want more compression, less attack, and to lower the voltages in these amps. The GT-5Y3 rectifier gives a nice feel to these amps with a much slower rise time than the 5AR4 or the 5U4, with a great feel. The Groove Tubes GT-5Y3 rectifier will also let amps such as the Matchless distort at a lower volume to make them suitable for smaller venues and to record sweetly at lower settings.Country of origin: RussiaCountry of origin: Russia

Groove Tubes Gold Series Gt-5Y3 Gz30 Rectifier Tube $17.99 The Groove Tubes Gold Series GT-5Y3″GZ30 is a rectifier tube common to lower-powered Fender amplifiers such as the Champ, Princeton and Deluxe amps. This Gold Series vacuum tube can be used in many 5AR4 and 5U4 amps for lower levels. This Groove Tubes rectifier may be used in amps such as the Matchless DC-30 series and similar amps when you want more compression, less attack, and to lower the voltages in these amps. The GT-5Y3 rectifier gives a nice feel to these amps with a much slower rise time than the 5AR4 or the 5U4, with a great feel. The Groove Tubes GT-5Y3 rectifier will also let amps such as the Matchless distort at a lower volume to make them suitable for smaller venues and to record sweetly at lower settings.Country of origin: RussiaCountry of origin: Russia

Groove Tubes Gold Series GT-5AR4/GZ34 Rectifier Tube $20.95 The most common rectifier tube used in higher powered amps which use a rectifier such as Fender 40 watt and Vox AC-30 amplifiers. Common to higher powered tube amps, like the later Fender Super Reverb amps and the Vox AC30 (or Matchless copies). May be used to replace a 5U4 or 5Y3 and will give a faster more dynamic tonal result. This rectifier has a rise time from 300-400 volts that is about 1/2 that of a 5U4. They work nicely in amps such as the Mesa Rectifier series which use the 5U4. Great if you want a feel and response that is tighter than stock rectifiers yet you want to retain the feel and compression character of a vacuum rectifier over the solid-state setting.   Country of origin: RussiaCountry of origin: Russia

Fender Champion Vintage Modified Amps 2330100000 600 Tube Electric Guitar Amplifier – 1 x 6 inches Speaker – Two Tone $87.49 A fun and affordable tribute to a rare historic Fender model. The Champion 600 is a five watts tube guitar amplifier with a 6 inch speaker and a 50s style two tone look. The added higher gain preamp circuit takes the overdriven tone beyond that of the original, with a choice of high or low gain inputs. Internal speaker output jack allows use of a larger speaker cabinet.

Groove Tubes Gold Series Gt-5Ar4/Gz34 Rectifier Tube $20.95 The most common rectifier tube used in higher powered amps which use a rectifier such as Fender 40 watt and Vox AC-30 amplifiers. Common to higher powered tube amps, like the later Fender Super Reverb amps and the Vox AC30 (or Matchless copies). May be used to replace a 5U4 or 5Y3 and will give a faster more dynamic tonal result. This rectifier has a rise time from 300-400 volts that is about 1/2 that of a 5U4. They work nicely in amps such as the Mesa Rectifier series which use the 5U4. Great if you want a feel and response that is tighter than stock rectifiers yet you want to retain the feel and compression character of a vacuum rectifier over the solid-state setting. Country of origin: RussiaCountry of origin: Russia

Used Jacques Tb-2 Tube Blower Overdrive Pedal $113.06 The Jacques TB-2 Tube Blower is an overdrive pedal designed in the tradition of the original Ibanez ts808. The Jacques Tube Blower is a boutique pedal that improves on the legendary Tube Screamer’s performance by adding more gain, continuous morphing from clean to gain, bass boost a la Marshall amps, and treble boost a la Fender black face amps. The Tube Blower also offers you full single-coil and humbucker compatibility, transparency to the amp, transparency to the guitar and playing style, and a classic look. The Jacques TB-2 Tube Blower Overdrive Pedal also give you low and high boost, drive, and level controls.Designed after the Ibanez ts808More gainContinuous morphing from clean to gainBass boost a la Marshall ampsTreble boost a la Fender black face ampsFull single-coil and humbucker compatibilityTransparency to the ampTransparency to the guitar and playing styleClassic lookLow and high boost controlsDrive controlLevel controls

Jacques Tb-2 Tube Blower Overdrive Pedal $129.95 The Jacques TB-2 Tube Blower is an overdrive pedal designed in the tradition of the original Ibanez ts808. The Jacques Tube Blower is a boutique pedal that improves on the legendary Tube Screamer’s performance by adding more gain, continuous morphing from clean to gain, bass boost a la Marshall amps, and treble boost a la Fender black face amps. The Tube Blower also offers you full single-coil and humbucker compatibility, transparency to the amp, transparency to the guitar and playing style, and a classic look. The Jacques TB-2 Tube Blower Overdrive Pedal also give you low and high boost, drive, and level controls.Designed after the Ibanez ts808More gainContinuous morphing from clean to gainBass boost a la Marshall ampsTreble boost a la Fender black face ampsFull single-coil and humbucker compatibilityTransparency to the ampTransparency to the guitar and playing styleClassic lookLow and high boost controlsDrive controlLevel controls

Groove Tubes Gold Series GT-12AX7-R Preamp Tube $16.95 The Groove Tubes Gold Series GT-12AX7-R Preamp Tube is an older-style Russian-type vacuum tube with strong tone and a slightly edgy tone. This newer tube from Russia has slightly brighter and lower gain, quicker compression than the GT 12AX7. Great for most Fender amplifiers, especially lower gain Fender-type amps. Country of origin: RussiaCountry of origin: Russia

Groove Tubes Gold Series Gt-12Ax7-R Preamp Tube $16.95 The Groove Tubes Gold Series GT-12AX7-R Preamp Tube is an older-style Russian-type vacuum tube with strong tone and a slightly edgy tone. This newer tube from Russia has slightly brighter and lower gain, quicker compression than the GT 12AX7. Great for most Fender amplifiers, especially lower gain Fender-type amps. Country of origin: RussiaCountry of origin: Russia

Fender GT6550 Tube Blue Duet $78.29 Fender tube amps now come factory equipped with matched Groove tubes. Because they are color coded and matched, no re-biasing is needed. You simply match the red, blue or white color coding when replacing them. They give you better harmonic balance, longer life, matched gain to distortion ratio, plus a wider frequency response than any other tubes available.

Fender GT6550 Tube White Duet $89.99 Fender tube amps now come factory equipped with matched Groove tubes. Because they are color coded and matched, no re-biasing is needed. You simply match the red, blue or white color coding when replacing them. They give you better harmonic balance, longer life, matched gain to distortion ratio, plus a wider frequency response than any other tubes available.

Fender Gt6550 Tube White Duet $89.99 Fender tube amps now come factory equipped with matched Groove tubes. Because they are color coded and matched, no re-biasing is needed. You simply match the red, blue or white color coding when replacing them. They give you better harmonic balance, longer life, matched gain to distortion ratio, plus a wider frequency response than any other tubes available.

AXL Akita AT40 Tube Amp $674.99 AXL Akita AT40 Tube Amp AXL Akita AT40 Tube Amp Description: With a vintage design and classic features recalling the most popular amps of the late 60′s, the all-tube Akita Series give you incredible output power and tons of tube tone. Each amp comes equipped with Accutronics reverb for modern or vintage tones, plus an overdrive channel with distortion. All tubes on the Akita Series are pre-tested premium tubes. Akita Amps get astonishingly loud, bringing the classic tube tone to a new generation of players. Available in a birch plywood veneer or blonde tolex cabinet. AXL Akita AT40 Tube Amp Features: 40 Watts RMS Preamp: 4 x 12AX7 Power Amp: 4 x EL84 2 x 12″ Alphatone Speakers Accutronics Spring Reverb Clean & Overdrive Channels AXL Akita AT40 Tube Amp Specifications: 40 Watts RMS Preamp: 4 x 12AX7 Power Amp: 4 x EL84 2 x 12″ Alphatone Speaker Accutronics Spring Reverb Clean Channel Overdrive Channel with Gain Control Channels Remotely Switchable 3-Band EQ Effects Send & Return 1/4″ Input 1/4″ Speaker Output Standby Switch Copper-Plated Control Knobs Birch Plywood Veneer or Blonde Tolex Cabinet Vintage Pattern Grille Cloth 22″ x 26.25″ x 13.5″ at 62 lbs. Get your AXL Akita AT40 Tube Amp today!

Groove Tubes Silver Series ST-EL84-S Power Tube $13.95 The Silver Series ST-EL84-S Power Tube is Groove Tubes’ European version with even more response, higher power and warmer tone. Good quality, long lasting type vacuum tube with a slightly aggressive edge when pushed into overdrive. Most common low power pentode, popularized in early Vox AC30 amps. Quick, soft overdrive distortion, a great power tube for recording.Country of origin: SlovakiaNEW SILVER SERIES TUBESGroove Tubes Silver Series are tested and warranted to meet or exceed factory specifications.Silver Series tubes are excellent for “normal” tube replacement applications and offer exceptional value.Not recommended for the critical high gain V1 stages of high gain guitar amps, but perfect for the other less critical stages such as V2-V6 stages.Country of origin: Slovakia

AXL Akita AT20 Tube Amp $412.49 AXL Akita AT20 Tube Amp AXL Akita AT20 Tube Amp Description: With a vintage design and classic features recalling the most popular amps of the late 60′s, the Akita Series give you incredible output power and tons of tube tone. Each amp comes equipped with Accutronics reverb for modern or vintage tones, plus an overdrive channel with distortion. All tubes on the Akita Series are pre-tested premium tubes. Akita Amps get astonishingly loud, bringing the classic tube tone to a new generation of players. Available in a birch plywood veneer or blonde tolex cabinet. AXL Akita AT20 Tube Amp Features: 20 Watts RMS Preamp: 1 x 12AX7 Power Amp: 2 x EL84 10″ Alphatone Speakers Accutronics Spring Reverb Clean & Overdrive Channels AXL Akita AT20 Tube Amp Specifications: 20 Watts RMS Preamp: 1 x 12AX7 Power Amp: 2 x EL84 10″ Alphatone Speaker Accutronics Spring Reverb Clean Channel Overdrive Channel with Gain Control Channels Remotely Switchable 3-Band EQ Effects Send & Return 1/4″ Input 1/4″ Speaker Output Standby Switch Copper-Plated Control Knobs Birch Plywood Veneer or Blonde Tolex Cabinet Vintage Pattern Grille Cloth 16″ x 18″ x 10″ at 32 lbs. Get your AXL Akita AT20 Tube Amp today!

AXL Akita AT30 Tube Amp $487.49 AXL Akita AT30 Tube Amp AXL Akita AT30 Tube Amp Description: With a vintage design and classic features recalling the most popular amps of the late 60′s, the Akita Series give you incredible output power and tons of tube tone. Each amp comes equipped with Accutronics reverb for modern or vintage tones, plus an overdrive channel with distortion. All tubes on the Akita Series are pre-tested premium tubes. Akita Amps get astonishingly loud, bringing the classic tube tone to a new generation of players. Available in a birch plywood veneer or blonde tolex cabinet. AXL Akita AT30 Tube Amp Features: 30 Watts RMS Preamp: 2 x 12AX7 Power Amp: 2 x 6L6GC 12″ Alphatone Speakers Accutronics Spring Reverb Clean & Overdrive Channels AXL Akita AT30 Tube Amp Specifications: 30 Watts RMS Preamp: 2 x 12AX7 Power Amp: 2 x 6L6GC 12″ Alphatone Speaker Accutronics Spring Reverb Clean Channel Overdrive Channel with Gain Control Channels Remotely Switchable 3-Band EQ Effects Send & Return 1/4″ Input 1/4″ Speaker Output Standby Switch Copper-Plated Control Knobs Birch Plywood Veneer or Blonde Tolex Cabinet Vintage Pattern Grille Cloth 18″ x 19.5″ x 11″ at 40 lbs. Get your AXL Akita AT30 Tube Amp today!

Groove Tubes Silver Series St-El84-S Power Tube $13.95 The Silver Series ST-EL84-S Power Tube is Groove Tubes’ European version with even more response, higher power and warmer tone. Good quality, long lasting type vacuum tube with a slightly aggressive edge when pushed into overdrive. Most common low power pentode, popularized in early Vox AC30 amps. Quick, soft overdrive distortion, a great power tube for recording.Country of origin: SlovakiaNEW SILVER SERIES TUBESGroove Tubes Silver Series are tested and warranted to meet or exceed factory specifications.Silver Series tubes are excellent for “normal” tube replacement applications and offer exceptional value.Not recommended for the critical high gain V1 stages of high gain guitar amps, but perfect for the other less critical stages such as V2-V6 stages.Country of origin: Slovakia

Fender Hot Rod Deluxe 40-Watt Tube Guitar Amplifier $599.99 The Hot Rod Deluxe is the world standard for portable, powerful, full-featured tube amps. Awe inspiring Fender tone issues forth from a 12″ Special Design Eminence Speaker fueled by a pair of Groove Tube 6L6 power tubes and three 12AX7 preamp tubes.

Groove Tubes GT-12AY7 Select Preamp Tube $32.99 The Groove Tubes GT-12AY7 Select Preamp Tube is closest in specification to a 12AX7 and can be exchanged with a slight drop in gain. Most companies changed over to the 12AX7 as it became more common. This tube can be tried in later Marshall amplifiers in the first gain position, where the owner of these amps would like to drop the background noise and lower the gain level to plexi or early 70′s vintage gain levels with its returned wider frequency response.Country of origin: RussiaCountry of origin: Russia

Groove Tubes Silver Series ST-12AX7-R Preamp Tube $11.95 The Groove Tubes Silver Series ST-12AX7-R Preamp Tube is intended as a replacement for tubes that will receive normal service.Country of origin: RussiaNEW SILVER SERIES TUBESGroove Tubes Silver Series are tested and warranted to meet or exceed factory specifications.Silver Series tubes are excellent for “normal” tube replacement applications and offer exceptional value.Not recommended for the critical high gain V1 stages of high gain guitar amps, but perfect for the other less critical stages such as V2-V6 stages.Country of origin: Russia

Groove Tubes Gt-12Ay7 Select Preamp Tube $32.99 The Groove Tubes GT-12AY7 Select Preamp Tube is closest in specification to a 12AX7 and can be exchanged with a slight drop in gain. Most companies changed over to the 12AX7 as it became more common. This tube can be tried in later Marshall amplifiers in the first gain position, where the owner of these amps would like to drop the background noise and lower the gain level to plexi or early 70′s vintage gain levels with its returned wider frequency response.Country of origin: RussiaCountry of origin: Russia

Groove Tubes Silver Series St-12Ax7-R Preamp Tube $11.95 The Groove Tubes Silver Series ST-12AX7-R Preamp Tube is intended as a replacement for tubes that will receive normal service.Country of origin: RussiaNEW SILVER SERIES TUBESGroove Tubes Silver Series are tested and warranted to meet or exceed factory specifications.Silver Series tubes are excellent for “normal” tube replacement applications and offer exceptional value.Not recommended for the critical high gain V1 stages of high gain guitar amps, but perfect for the other less critical stages such as V2-V6 stages.Country of origin: Russia

Tube-Tech Pe-1C Program Equalizer $2475 The Tube-Tech PE 1C Program Equalizer is the design that started it all for John Petersen and Tube-Tech. It’s an all tube version of the legendary Pultec EQP 1A, an equalizer that was, and still is, known for its uncanny ability to make things sound better by just running signal through it. Has Tube-Tech captured that magic? Just do a Google search for Tube-Tech PE 1C. Page after page of world class and mid- to upper-level recording studios come up. That alone tells the whole story. Tube-Tech PE 1C Program Equalizer, First Take:Passive Pultec-style EQTube-based gain-makeup ampliferBalanced I/O and Floating TransformersPassive EQThe PE 1C contains a passive filter and a tube-based amplifier to restore the loss from the filter. The filter has a low frequency boost/attenuate section with 4 selective frequencies, a high frequency boost section with a variable bandwidth and 10 selective frequencies and a high-frequency attenuation section with 3 selective frequencies. The filter is placed directly after the input transformer therefore eliminating noise from the amplifier when boosting either low or high frequencies. The amplifier consists of two tubes (valves) in push-pull configuration (one ECC 83 as the pre-amp and phase splitter, and one ECC 82 as the output stage), and an output transformer. Both input and output are balanced and fully floating. The in/out key switches the filter in and out without clicks and changes in level, while the amplifier remain in the signal path.Balanced I/O and Floating TransformersInput and output are balanced as well as fully floating. This provides maximum electronic isolation for superior noise rejection. The power supply for the pre-amp and phase splitter are stabilized and the heaters of both tubes (valves) are fed with a stabilized DC voltage. This prevents any variation in the DC energy when combined with the musical signal, which would otherwise cause certain types of distortion. Put simply, the PE 1C’s DC-stabilized circuits keep the EQ bands free of any unwanted artifacts. EQ is smooth and distortion-free. About Tube-TechFor over twenty years, Tube Tech has been one of the most prominent names in all-tube signal processing equipment. You’ll find their gear in the best recording and mastering studios around the world. The company’s founder, John Petersen is an electrical engineer who was factory trained at Solid State Logic, EMT, Studer, Sony, Neumann, and NTP Electonik (digital audio routers). He also designed tape recorder playback/recording amps for Lyrec tape recorders (found in the studios of the legendary Joe Meek and Vangelis). His first design under the name of Tube-Tech was an all-tube equalizer based on the legendary Pultec EQP 1A. Petersen continued to design and manufacture a number of innovative all-tube outboard processors including preamps, multiband compressors and summing amps. Thanks to John’s dedication to high-quality analog sound you’ll see Tube-Tech gear in the racks of pro audio legends

Manley Dual Mono Tube Direct Interface $1350 The Manley Dual Mono Tube Direct Interface offers the flexibility that allows the user to create stereo recordings or simultaneously go direct with two separate instruments. This outstanding DI Box features exceptionally clean and quiet tube circuits, which will warm up any electric guitar, bass, violin, and especially those sterile sounding synths. Unique with the Manley Tube DI is the added 5-position high pass shelf EQ, there to fight unwanted resonances. As a splitter device, the transformer-coupled balanced XLR output can be sent directly to a mic level input, such as through your console channel, while the 1/4″ output drives the guitar amplifier cabinet, which can be miked and mixed with the direct feed. Low impedance outputs, Ground lift and Console Out Boost switches make the Manley DI Box both versatile and compatible. It turns that noisy high impedance guitar cable into quiet lo-Z territory fast! Keep your Manley Dual Mono DI close at hand to solve a variety of studio problems and improve the quality of your recordings.Type: Dual Mono All Tube Direct Interface Vacuum Tube: 5751 Gain: -6dB or -26dB Input Z: 10 Mohm to 1 Mohm Output Z: 150 ohm xfmr Frequency response: 12 Hz – 15KHz (-3dB) EQ: LF rolloff -3dB points: 12, 42, 100, 250Hz Transformer-Coupled Balanced XLR Output Console Out Boost Switch Ground Lift Switch Factory set for 100V, 120V or 220-240VAC operation for original destination country’s mains voltage. Operating Mains Voltage changeable with power transformer re-wiring and fuse value change. Mains Voltage Frequency: 50~ 60Hz Mains power consumption Mono Tube DI: 0.050 Amps (50 milliamps = 50mA) @ 120V = 6 Watts 0.025 Amps (25 milliamps = 25mA) @ 240V = 6 Watts Mains power consumption Stereo Tube DI: 0.0750 Amps (75 milliamps = 75mA) @ 120V = 9 Watts 0.0375 Amps (37.5 milliamps = 37.5mA) @ 240V = 9 Watts

Groove Tubes Gold Series Gt-12At7 Preamp Tube $13.29 The Groove Tubes GT-12AT7 preamp tube is manufactured to the highest quality JAN spec. NOS, made in Russia for extremely long life. Used widely in most U.S.-made amps and, in particular, Fender amps. Fender amps with reverb use 2 – 12AT7s — one for the reverb drive stage, and one as a phase inverter to drive the push/pull output stage. The makeup of the 12AT7 is very similar to the 12AX7 and it can be substituted for a 12AX7 in a pinch. Some players prefer the 12AT7 in the driver stage of a Marshall for a cleaner, brighter tone. (The driver or phase inverter is the 12AX7 located nearest the power tubes.) The 12AT7 is rarely used in a tone-generating stage, but rather in function stages, so the Groove Tubes GT-12AT7 is selected for durability.Country of origin: RussiaTested under extreme conditionsGuaranteed free of excess noise and squealJAN spec.MilitaryNOSExtremely long lifeCountry of origin: Russia

Hal Leonard All About Vacuum Tube Guitar Amplifiers Book $31.46 Explores all manufacturers and de-mystifys the inner workings of tube amps. All new material from the amp guru Gerald Weber. Tons of empirical data that de-mystify the inner workings of tube amps to help you get the most from your amps! You will learn how tube amps work, electronic concepts, how different types of tubes work, the anatomy of a gain stage, how to resurrect a dormant tube amp, how to do a cap job correctly, modifications to preserve your amp, how to voice an amp and tune the reverb, how to build an amp, recover a cabinet, re-grill a baffleboard, how to buy a vintage amp; and common wiring mistakes and idiosyncrasies found in vintage amps. And you get a couple of hundred pages of Questions and Answers – sectioned off into Fender, Gibson, Marshall, Danelectro/Silvertone, Vox, Other American, Other British and Miscellaneous Topics. You will learn the six dreaded tone killers and how to avoid them, the top ten amp-tone tips, and how to fine-tune your entire amp setup. In short, you will have the knowledge needed to squeeze your amp’s performance from lame to insane.

You can also browse hot deals from Amazon on Tube Amps

Waring MG100 300-Watt Meat Grinder, Brushed Stainless Steel $77.30 Engineered by Waring, this versatile meat grinder helps you ensure that the food you cook is as fresh as possible. Suitable for home use, the machine grinds beef for tacos, turkey for burgers, and pork for sausage, as well as non-meat items like vegetables and fruit. Powered by a 150-watt motor, the grinder has a durable die-cast metal hopper and brushed stainless-steel housing. It comes with thre…

29 Twin Tub Portable Washer with 10 lb. Capacity 2 Wash Options Lint Filter & Separate Spin Extractor $314.90 The Danby DTT420 Twin Tub Washer features a large wash tub and separate high speed spin extractor Designed to save on energy costs the Twin Tub Washer uses less than 200 watts of electricity per load This Twin Tub Washer has a 10 lb tub capacity and…

Grand & Benedicts Store 2 Ft. Rectangular Hangrail Tube $10.44 Hangrail tube, 2′, rect. 6009974…

Revelator $8.64 Revelator is the long-awaited, song-oriented debut album by the husband-wife team of singer/guitarist Susan Tedeschi and guitarist Derek Trucks. Filled with smoky, blues-dipped rockers and heart-stilling ballads that show off, respectively, the gutsier and softer side of Tedeschi’s vocal ability, plus a series of emotive, story-telling solos shaped by Trucks’s uncanny agility on slide-guitar, Reve…

Understanding Tube Amps $40.75 Series: DVD Publisher: Kendrick Videos Format: DVD Author: Gerald Weber Kendrick Amplifiers President Gerald Weber has overhauled and serviced over 15,000 vacuum tube guitar amplifiers, designed dozens of new model amplifiers and has produced thousands of boutique tube guitar amplifiers. This DVD will transform your experience of tube guitar amplifiers forever. Whether you are a beginner or …

Stink Bomb $10.31 …

Tube Guitar Amplifier Servicing & Overhaul $40.51 Kendrick Amplifier President and Vintage Guitar magazine columnist Gerald Weber has overhauled and restored over 15,000 vintage tube guitar amps. This extensive DVD covers: basics of servicing and overhauling a tube guitar amp, what tools are needed, the wiring mistake made on 50% of all amps and how to correct it, the best way to straighten preamp tube pins, how to perform a cap job correctly, th…

Sylvania 22181 32-Watt T8 Octron Fluorescent Ecologic Lamp 4100K 75 CRI with Instant Start or Rapid Start, Cool White, 12 Pack $29.98 mfr: SYLVANIA LIGHTING Suitable for instant start or rapid start operation. 75 CRI, 4100K color temperature. 20,000 average life hours. 48″ overall length. MEDIUM BI-PIN BASE – 1.1″ DIAMETER T8 – Boxed Watts=32 This item cannot be shipped to APO/FPO addresses. THIS ITEM CANNOT BE RETURNED. Please accept our apologies…

Welch Allyn Otoscope Insufflator Bulb & Tube W/Tip (21504) $4.99 Welch Allyn Otoscope Insufflator Bulb & Tube W/Tip (21504)…

Hope In a Tube – High Density Eye & Lip Firming Cream – Philosophy – Eye Care – 7.1g/0.25oz $19.97 An anti-wrinkle moisturizer for the eyes & lips Contains a synergistic blend of topical vitamins E & C Increase firmness & density of delicate skin around eyes & lips Visibly reduces appearance of fine lines & wrinkles Leaves skin velvety smooth, resilient & youthful – Philosophy – Eye Care…

Various kinds of guitar amps

Once you selected the guitar, the person needs a good amp to use a guitar. Now a day there are different varieties of configuration found in guitar they are

1.    Size
2.    Sound  and amplifier

These are the different types of configuration present in the guitar.

There are some useful tips to help the people to know more information about guitar and its different types of amps.

The different types of amplifiers is list below

The amplifiers consist of 4 types they are

1.    Solid-state(analog) amplifier
2.    Tube amplifier
3.    Modeling(digital) amplifier
4.    Hybrids amplifier

These are the 4 different types of amplifiers.

Solid-state Amps:

The guitars amps are familiar with the solid-state the solid-state is used in the transistors for getting more power sections. The amps are really responsible very rarely they need to repairs. The solid-state generally have the fresh tone, although some of the person will come with the twist too. The different types of amps mingle with players and give us the strong music, and it depends upon the touring amp so this is also known as solid-state amps and its uses.

Tube Amps:

The tube amps help many guitarists for their moderate performance, in guitar the amp consist of manly tone and also the natural twist is there in this tube amps. Usually the tube amps sound is heavier than the solid-state amps but in this we are using same wattage used in the solid-state amps but in tube amps only we can feel the accurate sound, but we cannot expect this from solid-state amps. Many of the tube amps have different variety of channels it can be controlled from the unclear tones immediately. Tube performance can be worsening the over time, so tubes should be changed rarely so this is also known as tube amps and its uses.

Modeling amps (Digital amps)-the modeling amp is used for the digital processors to replicate the sound will be fixed and modern tube technology. With the help of the models the sound tube amplifiers and cabinets are used to put the sound in different types of amps in one box so that the sound can travel in a single way. The modeling amps are changeable; regularly they select the digital sound effects like delay, chorus, etc .for this purpose the modeling amp is used the few will compromise of digital or analog outputs  with the narrator simulation for going the recording border of a system so this is also known as modeling amps(digital amps)and its uses.

Hybrid Amps- Merging the most important kind of guitar amp into the single package, these amps is used for the real tube combination with the help of solid state power part. The Marshall valve state amps is used for  pre-defined part and solid-state circuitry in the section of power to make a tube tone with no compulsory use of the power tubes so this is also known as hybrid amps and its uses.

So these are the different types of amplifiers and its uses.

About the Author

Alex is a Professional writer working with Gigasonic and he writes articles for Cubase Bundle for sale. He written many articles like Shure wireless and Steinberg software. For more information about all our services, go to http://www.gigasonic.com

Tube Amps 101 repairs, maintenance and more